Composés fluorés antimicrobiens : synthèse de monomères, élaboration de polymères, études physico-chimiques et biologiques
Institution:
NiceDisciplines:
Directors:
Abstract EN:
Today, Health Personnel are extremely cautious to avoid inert surfaces contamination by micro-organisms. However, despite the use of disinfectants, antibiotics, and the setting of strict hygienic conditions, it seems that nosocomial infections control such as, amongst others, infections resulting from operations, remains one of the major challenges for medicine. The objective of this manuscript is to present the modification of an inert material (glass, plastic, metal) after application of a biocidal polymer on its surface so as to make it bioactive. Our research work revolves around the preparation and the evaluation of fluorinated polymers and copolymers of quaternary ammonium type. We have prepared new series of polymerizable quaternary ammonium salts, hydrocarbon and fluorinated, precursor of the expected polyammoniums. The physico-chemical properties in solution of the obtained surfactants (CMC, γCMC) were evaluated previous to the measurement of the antimicrobial activity of these structures by determining their minimum inhibitory (MIC) and lethal concentrations (MLC), doing so for four characteristic micro-organisms. A set of potentially bioactive homopolymers and copolymers was prepared. The various tests of solubility have showed that the copolymers were water-soluble, and that the homopolymers alone, due to their water-insolubility, could be used as coatings for an antimicrobial contact activity test. Therefore, we have worked out, validated, and then used a biological activity test by contact against Staphylococcus aureus. For the most efficient coatings, the reduction of the bacterial population was above 99,95% after 24 hours of contact. For copolymers, the antimicrobial activity in solution was above the corresponding monomers.
Abstract FR:
Les personnels de santé prennent aujourd’hui des précautions multiples pour éviter la contamination des surfaces inertes par des micro-organismes. Toutefois, malgré l’utilisation de désinfectants, d’antibiotiques et la mise en place de conditions d’hygiène strictes, il apparaît que la lutte contre les infections nosocomiales telles que, entre autres, les infections opératoires, est aujourd’hui un des défis majeurs de la médecine. L’objectif de ce manuscrit est de présenter la modification d’un matériau inerte (verre, plastique, métal), par dépôt d’un polymère biocide en surface, afin de le rendre bioactif. Notre travail de recherche s’articule autour de la préparation et de l’évaluation de polymères et copolymères fluorés de type polyammoniums quaternaires. Nous avons préparé un ensemble de sels d’ammoniums quaternaires polymérisables, hydrocarbonés et fluorés, précurseurs des polyammoniums envisagés. Les propriétés physico-chimiques en solution (CMC, γCMC) des tensioactifs obtenus ont été évaluées, avant de mesurer l’activité antimicrobienne de ces structures en déterminant respectivement la concentration minimales d’inhibition (CMI) et la concentration minimale létale (CML), pour quatre micro-organismes caractéristiques. Un ensemble d’homopolymères et copolymères, potentiellement bioactifs, a été préparé. Les différents essais de solubilité ont montré que les copolymères étaient hydrosolubles et que seuls les homopolymères, du fait de leur insolubilité dans l’eau, pouvaient être utilisés sous forme de revêtements dans le cadre d’un test d’activité biologique de surface. Nous avons alors mis au point, validé puis utilisé un test d’activité biologique par contact vis-à-vis de Staphylococcus aureus. Dans le cas des revêtements les plus performants, la réduction de la population bactérienne est supérieure à 99,95% après 24 heures de contact. Pour les copolymères, l’activité antimicrobienne en solution est supérieure à celle des monomères correspondants.